System Sensor Duct Detector Sampling Tube

The end cap is needed to create the proper air flow to the sensor of the duct smoke detector. Otherwise trim the end of the tube pro truding through the duct so that 1 to 2 inches of the tube extends outside the duct. A plastic exhaust tube is included with the unit to be installed if needed.

3099 4951 6963 9225 9827 1293 5481 6706 2676 6907 4515 5463 6360 901 4946 2831 962 1386 7860 3901 7803 3897 7563 6419 8313 8356 5029 3495 3769 1561 2740 5917 35 5368 1527 6389 9264 5286 199 5747 1436 6974 5360 6834 2937 5509 3759 6078 7308 9806 5662 1280 4258 4182 5396 6240 1923 2579 2280 4903 9473 7832 1990 7065 3284 9602 2436 7034 3407 1059 2666 6270 7000 4681 89 3514 9162 9317 9444 1295 6124 8455 3615 48 2328 8938 8850 6532 3557 4360 9885 6860 258 3688 4863 1238 9491 5104 4904 6672 7719 4714 4349 4245 457 8928 2618 4794 1976 1864 9091 6808 9484 9120 6520 6453 1659 4967 9254 800 9070 51 4795 9698 7252 3595 2069 8417 3887 3386 5070 961 2122 790 9693 2630 4909 3540 7550 9009 9957 3823 9058 1912 1880 8406 4059 7011 2909 1401 7033 8187 5692 6352 3948 5491 855 1489 1368 7095 9703 4429 9418 8534 1394 3302 816 4708 5568 1710 1794 278 820 9820 3515 7776 5435 3668 1650 2603 6492 7774 890 8897 9729 4761 2444 2031 5953 2791 3856 6778 4897 8078 5490 5961 8500 4473 9343

System Sensor Dnre Duct Detector Housing With B501ap Base

True Duct Smoke Detectors With Relay Output And Analogue Output Vsd Series Ventilation Control Products Sweden Ab

Intelligent Dnre Duct Smoke Detector En

System Sensor Dst5 Duct Mounted Smoke Detector Sampling Tube 4 To 8 Ft Width Duct

Dst Sampling Tubes For Duct Smoke Detectors En

How To Remove Pipe Inside Duct Detector From System Sensor Youtube

System sensor provides system flexibility with a variety of accessories including two remote test stations and several different means of visible and audible system annunciation.

System sensor duct detector sampling tube.

As with our duct detectors all duct smoke detector accessories are ul listed. The end cap is needed to create the proper air flow to the sensor of the duct smoke detector. If the tube is shorter than the width of the air duct install the end plug into the inlet tube as shown in figure 4and support the end opposite the duct detector. A plastic exhaust tube is included with the unit.

As with our duct detectors all duct smoke detector accessories are ul listed. Sampling of air in ducts wider than 8 feet is accomplished by using the st 10 inlet sampling tube. There are more than 2 holes in the section of the tube extending out of the duct select a different tube length using table 1. A plastic exhaust tube is included with the unit to be installed if needed.

Air duct detector inlet sampling tube. Dst sampling tubes for duct smoke detectors the dst family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct. The sampling tube must be purchased separately. The correct length has to be chosen for width of the duct where it will be installed.

As with our duct detectors all duct smoke detector accessories are ul listed. Install the inlet tube as follows. Dst sampling tubes for duct smoke detectors the dst family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct. Once any sampling tube length adjustments are made plug the end of the sampling tube with the provided end cap.

The end cap is needed to create the proper air flow to the sensor of the duct smoke detector. System sensor provides system flexibility with a variety of accessories including two remote test stations and several different means of visible and audible system annunciation. System sensor provides system flexibility with a variety of accessories including two remote test stations and several different means of visible and audible system annunciation. Once any sampling tube length adjustments are made plug the end of the sampling tube with the provided end cap.

Install into the housing con nection that is downstream from the sampling tube connection. Once any sampling tube length adjustments are made plug the end of the sampling tube with the provided end cap.